How To Remove Caster Wheels From Chair

Download Article

Download Article

Casters can help your part chairs become more versatile, allowing y'all to scroll effectually on wheels instead of being stuck in one place. Notwithstanding, when your chair starts to wobble as y'all roll around your office, you might want to get your onetime casters replaced. Luckily, this is an easy process that merely requires a little elbow grease.

1. ane

   Plow the chair upside down. Place the head of the chair on the ground so that the wheels are in the air. This will help you have full access to the casters on the bottom of the chair.^[1]

   • If your chair is too heavy to turn upside down on your own, recruit a friend to assist you exercise it.

2. 2

   Remove a threaded caster by turning it clockwise. Casters with a threaded stem (basically a spiral) volition release once they've twisted out enough. Twist your caster clockwise to examination out which kind of caster it is: if it starts moving in the direction y'all're twisting, just go along going and it should come out.^[two]

   Advertisement

3. 3

   Uninstall a grip stem caster by lubricating and pulling on it. If it'south a grip stem (meaning information technology won't unscrew), employ lubricating oil to the spot where the caster meets the chair. Put ane hand on the caster and one hand on the chair leg, so give it a pull.^[3]

   • Use a spray oil like WD-40, which costs around $10 (£7.x) at a hardware shop.
   • Endeavour gripping it with a towel or glove if it doesn't budge.
   • Some office chairs will take a swivel plate (a square plate that attaches to the chair leg) instead of a stem, though this is unusual. If this is the case, simply use a screwdriver to remove the plate.

4. iv

   Use a screwdriver and pry bar if the caster won't budge. Some casters are besides rusted to pull out with your easily. Find the widest flat-head screwdriver yous can find (some screwdrivers tin can be as broad equally ^ane⁄_two  in (13 mm)) and a pry bar with a nail-pulling slot at the terminate.^[four]

   • The pry bar's nail-pulling slot should exist big enough to fit the stalk of the pulley, which is usually a piddling over ¹⁄_two  in (13 mm).

5. five

   Push the screwdriver's head where caster meets the chair, and so turn it. Get the screwdriver to where it's right in between the chair and the pulley itself. Turn the screwdriver slowly until the pulley starts to move upward, abroad from the chair.

   • If the caster won't move, try rotating it around the caster. Dissimilar angles may give you more leverage to pull the pulley out.

6. six

   Position the pry bar's nail-pulling slot over the stalk and pull it out. Take the pry bar and position the blast-pulling slot to where information technology's straight between the caster and the chair, over the stalk. Pull on the caster, and it should pop out.^[5]

   • If you take another person with you, try getting them to pull the office chair from the other side.

Advertisement

1. one

   Write downward the size of the caster'southward stalk and what kind of stem information technology is. Use a ruler to measure out the caster'south stem. The stem is the metal part that connects the caster to the chair. Also, write down whether or non the stalk is threaded or grip.^[6]

   • A threaded caster has a spiral that screws into the chair, while a grip stem pulls out like a plug from a socket.
   • If your chair has a swivel plate, measure the width of the plate itself.

2. 2

   Measure the wheel from front to back. Using a ruler, mensurate the wheel itself from the front to the back. Most casters come with two–ii.5 in (5.ane–six.iv cm) wheels.^[7]

   • If you've had difficulty rolling the chair around (say, onto an elevated surface like a carpeting), consider buying a larger bicycle.

3. 3

   Determine whether you desire a twin-wheel or unmarried-wheel pulley. A twin-wheel pulley tends to concluding longer, since it distributes weight more than evenly, merely a single-wheel caster is more reliable, since it has less opportunity to fail, having fewer parts.^[8]

   • Twin-wheel casters are more frequently used in part settings, while single-cycle casters are typically found in industrial settings.

4. 4

   Purchase rug casters for carpeted, soft surfaces. These casters are often fabricated with plastic and have a hood for hiding the carpeting threads that get together as the caster rolls across the flooring.^[9]

   • If your chair will be rolling on both carpeted and hardwood floors, it's best to go hard floor casters, as they're less dissentious to hard surfaces.

5. five

   Buy hard floor (sometimes chosen hard surface) casters for hardwood floors. These are made specifically to roll across hard floors without damaging the flooring.^[x]

   • Hard floor casters are also able to roll on carpets; they're but made to salve difficult floors from harm.

6. 6

   Buy your new casters from an office supply store. Casters can be bought from any hardware store or online hardware store. Exist sure to take the specifications yous've written down with you lot, every bit yous'll want to be able to compare them and make sure you're buying the right product.

   • If you're shopping for your casters in-person, take one of the old casters with you lot and ask someone who works in that location to help you compare.

Ad

1. 1

   Screw in a threaded caster with your easily until it no longer turns. If your casters are threaded, marshal the threaded stem with chair's leg and screw it in until it stops turning.^[eleven]

2. 2

   Push in a grip caster. For a grip pulley (with a stem that is non threaded), push the caster's stalk into the chair leg until the pinnacle of the caster is flush with the lesser of the chair leg.^[12]

   • If the caster is difficult to go into the hole, add some lubricant (like WD-40) to the within of the leg or use a rubber mallet to drive the pulley in.

3. 3

   Install a swivel plate caster with a screwdriver. If your caster comes with a hinge plate, install it with the aforementioned screwdriver you used to uninstall the onetime caster.

Advertisement

Ask a Question

200 characters left

Include your e-mail address to get a message when this question is answered.

Submit

Advertisement

• Be sure to check your stalk measurements; with such small pieces, it's easy to misfile a measurement. For example, if you lot think your stem is ³⁄₈  in (9.v mm), apply a drill bit of ^three⁄_eight  in (ix.5 mm) and concord them upward to one another to make certain they're the verbal same size.

Thanks for submitting a tip for review!

Advertizement

About This Commodity

Thanks to all authors for creating a page that has been read 79,481 times.

Did this commodity assist y'all?

Source: https://www.wikihow.com/Replace-Office-Chair-Casters

Share this post